基于反问题的涡轮过渡流道一体化支板设计方法

为进一步改善大涵道比涡扇发动机气动性能及燃油经济性,降低其污染物排放,控制其重量与成本,提出了一种高效的高、低压涡轮过渡流道整流支板一体化设计理念,即对原型支板与第一级低压涡轮导叶进行初步正问题一体化设计,并基于气流角全三维粘性反问题进行进一步改型设计,使得在保证自身气动性能不降低的基础上,带一体化支板涡轮过渡流道能够与高、低压涡轮实现良好匹配。以某型发动机过渡流道为算例开展了一体化设计工作,并采用三维数值模拟方法进行了设计点、非设计点流场分析评估。结果表明,设计点工况下一体化支板出口气流角以及马赫数分布均与原型导叶出口一致,验证了一体化设计的有效性。同时,带一体化支板的过渡流道总压损失从原型流道的2.49%降低到了1.02%。而在非设计工况,带一体化支板的过渡流道气流分离明显减小,具有更宽的最佳工况范围。     

Potential of IRNSS/NavIC L5 signals for ionospheric studies

Indian Space Research Organization (ISRO) has developed an indigenous system named Indian Regional Navigation Satellite System (IRNSS) or NavIC (Navigation with Indian Constellation), that consists of 7 satellites and transmits navigation signal in L and S bands. ISRO, for validation of the system, has installed many IGS (IRNSS/GPS/SBAS) receivers scattered over the Indian region. Using preliminary data from two geographically widely separated stations over India, this paper presents the results on studies on parameters of IRNSS signal quality and discusses how these parameters may be used to study the ionospheric behavior over the Indian region. The results show the importance and advantages of using IRNSS data for such studies.     

基于Kriging模型梯度解析解的改进一次二阶矩方法

改进一次二阶矩（AFOSM）法是一种基于功能函数梯度的结构可靠性分析方法，鉴于其对隐式函数的梯度较难求解，提出了一种基于Kriging模型梯度解析解的AFOSM方法，利用Kriging代理模型的解析表达式推导得到功能函数对输入变量的梯度解析解，为AFOSM中设计点的确定提供高精度的梯度信息。通过Kriging与AFOSM的结合，很好地解决了基于有限元模型的隐式情况下梯度计算量相当大、可靠性分析难的问题。数值与工程算例验证了所提Kriging梯度解析解的较高精确性，同时验证了所提基于Kriging解析解的AFOSM结构可靠性分析方法的正确性与较高精度。     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

S弯二元喷管红外辐射特性实验

基于轴对称排气系统设计了一套S弯二元喷管的实验模型,在实验工况下测量了喷管实验件的部分流场参数和远场红外辐射特性,对S弯二元喷管的红外辐射特性进行了分析和研究,并与基准轴对称喷管的红外辐射实验结果进行了对比。结果表明:上方探测平面是S弯二元喷管的主要辐射方向,其最大辐射角度为15°,在该方向角上固体壁面辐射的贡献最大。下方和侧向探测平面各方向角的红外辐射强度明显小于上方探测平面,主要是由于S弯二元喷管遮挡了大部分的内部高温壁面。与基准轴对称喷管对比,S弯二元喷管有着明显的红外抑制作用,在尾部方向S弯二元喷管的积分辐射强度相比轴对称喷管降低了81%,最大辐射强度相比轴对称喷管降低了47%,燃气辐射降低50%。      

前飞速度和升力偏置量对共轴刚性旋翼气动特性影响分析

共轴刚性旋翼前飞状态的气动特性主要由工况环境中的来流速度、密度和桨叶的翼型配置、弦长分布和扭转分布等气动布局参数决定。气动布局参数的综合影响决定了共轴刚性旋翼的的升力偏置量。了解前飞速度和升力偏置量对前飞性能的影响规律有利于设计更适合于高速飞行的共轴刚性旋翼。因此,本文通过求解可压雷诺平均N-S(Reynolds-averaged Navier-Stokes,RANS)方程对4 m直径的由两副2片矩形桨叶旋翼构成的共轴刚性旋翼模型的前飞流场进行了数值模拟,获得了不同前进比下的气动力并对不同升力偏置量下的旋翼性能进行了对比。数值模拟结果表明,随前进比增大,桨叶展向拉力分布更加趋于合理,拉力中心向桨叶中段移动,可以充分给桨尖卸载;旋翼升力主要由前行侧桨叶提供,升力偏置量过大容易产生激波诱导失速,不利于高速前飞。     

基于流管试验的管道声传播预测

通过平板声衬流管试验，测试了管道内无流动和有流动下不同入射声波频率的管道壁面复声压，并基于试验模型与数据分别开展了二维和三维管道声传播预测，将试验测量结果与预测结果进行了对比。结果表明:二维和三维的预测结果非常吻合，尤其是在无流动条件下；在不同流动条件和不同频率下，声传播预测给出了与试验数据较为吻合的结果，壁面声压级的趋势与试验结果一致，基本验证了管道声传播预测模型的准确性；对比不同流动条件和频率点，有流动下预测的壁面声压级的误差比无流动更大，低频下预测的壁面声压级的误差比高频更大。      

基于两相流模型的挤压油膜阻尼器空化流场特性数值模拟

基于气液两相流理论中的Mixture模型和Zwart-Gerber-Belamri空化模型,采用动网格技术建立了两端开口中心槽供油型挤压油膜阻尼器三维非定常空化流场求解模型。数值模拟表明:随着阻尼器内环进动,考虑两相流动的油膜低压区在中心槽的两侧产生两道对称的条状负压带,条状带内具有较高的气相体积分数;阻尼器低压区的压力和气相体积分数对进油孔位置十分敏感,阻尼器油膜力和流场气穴比的变化频率与进油孔数密切相关。内环同心进动半径、进动频率对阻尼器空化流场影响的数值计算表明,进动半径和频率的增大均会使得流场内的空化现象加剧,同时气穴比的相位滞后现象愈加显著。      

Design and analysis of a truss deployable antenna mechanism based on a 3UU-3URU unit

Space deployable structures with large calibers, high accuracy, and large folding ratios are indispensable equipment in the aerospace field. Given that the single-DOF 3RR-3RRR deployable unit cannot be fully folded, this study proposes a 3UU-3URU deployable unit with two kinds of DOF: folding movement and orientation adjustment. First, based on the G-K formula, the DOF of the 3UU-3URU unit is analyzed. Then, the 3UU-3URU unit is used to construct a deployable truss antenna with a curved surface, and the DOF of the whole deployable antenna containing multiple 3UU-3URU units is calculated. The structural design of a deployable antenna with two loops is carried out with specific parameters and geometric relations. Next, a DOF simulation of a basic combination unit composed of three 3UU-3URU units is performed. Finally, a prototype of the basic combination unit is manufactured, and the DOF of the mechanism is experimentally verified.     

含多部位损伤搭接结构应力强度因子三维有限元分析

应力强度因子(Stress intensity factor,SIF)分析是含多部位损伤(Multiple site damage,MSD)结构剩余强度和裂纹扩展寿命预测的基础和关键。考虑接触与摩擦,建立了含MSD搭接结构的三维有限元模型,研究了不同裂纹长度、铆钉类型以及损伤模式下裂纹尖端SIF分布情况和变化规律。结果表明,搭接件孔边裂纹Ⅰ型SIF起主导作用,Ⅱ型和Ⅲ型SIF可忽略不计。由于次弯曲、铆钉变形和板厚度等因素,SIF在外表面最小,接触面一侧较大,最大值多位于蒙皮内部。MSD会使裂纹间的干涉作用增强,SIF增大,且裂纹间距离越近干涉作用越强。裂纹长度相同时,埋头铆钉的孔边裂纹SIF积分均值大于平头铆钉,且接触面的SIF埋头铆钉大于平头铆钉,外表面则相反。